Home > Other Fun Stuff > Actual Weights

Hitch Swings Pt. 1: Kuat Pivot adapts 2″ bike racks to swing freely from the vehicle

26 Comments
Support us! Bikerumor may earn a small commission from affiliate links in this article. Learn More

Hitch racks are great. They get the bikes out of the wind. They’re easy to load (especially with the tray style). And they are available in styles to fit a huge range of bikes. The one thing they’re not good for? Access to the trunk.

For years, this has been addressed with racks like the Yakima Full Swing, which allow the rack to swing away from the vehicle. However, they’ve almost always been limited to the traditional two-arm style rack – not all that convenient for modern mountain bikes, or bikes you don’t want banging into each other.

Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle

Because of that, 2017 must have been the year of the swing away platform rack as a few different brands launched new options. Among them – the new Kuat Pivot hitch adapter, and the Rocky Mounts Backstage.

Starting with the Kuat Pivot, this piece of hardware is obviously an adapter and not a complete rack. That gives you options when it comes to what you want to do with it. Partnering with RakAttach for the design, the Pivot is essentially a mass produced version of their medium RakAttach. That means it measures 30″ long, 8″ tall, and 15″ deep (measuring just the metal structure). Priced at $295, the Pivot includes a locking hitch pin, but you’ll still need to supply the bike rack.

Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle
Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicleAs a friend pointed out, the Pivot is a substantial piece of hardware. The steel construction of the 2″ only adapter results in a 47lb weight (46lb claimed). Remember that this is just for the adapter. Add in a two bike hitch rack like the Kuat NV 2.0 (which weighs 53.8lbs) and you’re looking at 100lbs before you add bikes. The good news is that the Pivot has a 250lb weight limit thanks to its burly construction so a four bike rack plus four reasonable bikes shouldn’t be a problem. And since the adapter is separate from the rack, you can take them apart to make it easier to move around the garage.

With all that weight, the Pivot needs to be stout to swing freely – and it is. Two thermoplastic skid plates are built into the bottom portion of the rack to support the upper structure and allow it to glide smoothly, and the pivot features massive hardware that’s up to the task.

Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicleHitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle

Equipped with a simple mechanical lock, the rack has an additional fail safe with the safety pin. To open the Pivot, flip the latch down, remove the pin, swing away, and install the pin in the corner hole to keep the rack in place. All of this can be done with the rack fully loaded for quick and easy access to the back of the vehicle.

Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle

As you might expect, once you mount the Pivot to the vehicle and then the rack to the Pivot, it does stick out quite a bit from the bumper. Depending on the rack that you’re using, you can choose one of two different mounting holes on the Pivot (shown above with the NV 2.0 in the hole closest to the vehicle.

Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle

Ironically, it sticks out far enough that I can open the tailgate on my Honda Element completely without needing to swing the rack away (with the rack empty).

Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle

And if you’re carrying road bikes, you might even be able to access the trunk without swinging the rack away when loaded as well. Mountain bike handlebars are wide enough that they prevent the upper hatch from clearing the handlebars, though.

Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle

This is what you’re really after though – completely unfettered access to the trunk. Whether you’re car camping, using the tailgate as a bench, or just trying to get big items in or out, this makes it all worth it. With or without bikes, the whole process takes seconds and very little strength. Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle

Unfortunately, it’s not all roses – at least for me. As I discovered on the Rocky Mounts Backstage as well, swing away racks can be a problem when it comes to exhaust pipe placement. On my Element (SC model, 2″ hitch), the Pivot sits directly in front of the exhaust pipe.

Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicleHitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle

The hitch itself has two mounting holes, but the Pivot requires the hole closest to the vehicle which makes the adapter sit closer to the bumper. That’s because the Pivot uses a hitch pin with a larger thread than most racks. On my hitch, only the first hole was big enough for the bolt to pass through it, so I’m forced to use that location. It also required removing some excess metal from the hitch (that’s utilized for mounting to a different vehicle) and cutting away some of the plastic to get the wrench in place. Fortunately, Kuat includes an 8mm allen fitting in the middle of the bolt so you don’t have to use the 24mm wrench.

As I found out on the Rocky Mounts Backstage (review to follow right after this one in part 2), the proximity of the rack to the exhaust can cause issues – like melted plastic pieces. On long drives, it also seems to cause exhaust soot to blow back onto the car, leaving the back end and the bikes coated in a fine dust (the photos above show the car covered in road salt, not exhaust soot).

Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle
Close, but not the solution I was looking for.
Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle
Even with the downturn tip, the rack still gets pretty hot.
Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle
Soot and moisture left on the rack after one drive with the new tip.

It was suggested that I try a different exhaust tip that pointed the exhaust gasses downward, away from the rack, but so far I haven’t found the right solution. I didn’t want to permanently alter the exhaust so I’ve been looking for a bolt-on tip in the right diameter, and the closest thing I’ve found so far doesn’t quite miss the rack. So far, nothing has melted on the Pivot, but it does get pretty hot after a short drive (the Rocky Mounts sits another 6″ away from the tail pipe and still reaches temperatures upwards of 130°f on a short drive). Fortunately there is a lot of metal to act as a heat sink, and if the skid plates don’t melt, there’s little plastic on the Pivot to worry about.

According to rack manufactures, the reason the adapters all sit to the right is so that the rack doesn’t swing into oncoming traffic if you’re parked on the street – which makes sense. Realistically, this will be a vehicle specific issue that may or may not actually be a problem. I’ll come back to this if I find a better answer for the exhaust issue short of replacing the entire tail pipe.

Hitch Swings Pt. 1: Kuat Pivot adapts 2" bike racks to swing freely from the vehicle

Overall, the Pivot seems to be an extremely well built piece of kit that provides a much needed feature to any 2″ bike rack. It is on the heavy side, but hopefully that’s an indication of durability down the road. If it wasn’t for the exhaust issue, I would recommend the Pivot in an instant. If your vehicle has the exhaust pipe on the left hand side or if it’s aimed in a way that that isn’t directly pointed at the rack, then absolutely. Otherwise, you may need to modify your exhaust to guarantee that there aren’t any issues. For now, I’ll keep using the Pivot to see if the exhaust will adversely affect the rack – or if it just gets dirty.

Want a specific swing away rack that’s lighter? We’ve got the Rocky Mounts Backstage review coming up next.

kuatracks.com

Subscribe
Notify of
guest

This site uses Akismet to reduce spam. Learn how your comment data is processed.

26 Comments
Oldest
Newest Most Voted
Inline Feedbacks
View all comments
Coloradohillman
Coloradohillman
6 years ago

Kuat Pivot is AWESOME!!! Mine solves all issues!!

Joe Rosario
Joe Rosario
6 years ago

Anyone have it on a Jeep Wrangler? Wondering if the swing out tailgate with a spare can be opened fully or will it bump into the bikes (Pivot swings to right as well as the tailgate)?

The Dude
The Dude
6 years ago
Reply to  Joe Rosario

https://www.saris.com/product/freedom-superclamp-st

Get that. it holds the bikes better than most other racks out there as well. just tire contact. 2 years on mine and it has been perfect.

Oderus
Oderus
6 years ago

Something to consider from a street legal standpoint. Any load coming off the car past X distance may be required to have reflectors, lights or a safety flag. Where I live the limit is 3ft off the back before additional safety warnings are required. My rack is just under 3 feet and this would push it beyond and into a traffic ticket if I didn’t know any better.

Dolan Halbrook
Dolan Halbrook
6 years ago

My NV+ with the extra 2 bike attachment is already ~85 lbs… I can’t imagine adding another 45 lbs to it.

Dude
Dude
6 years ago

Oof, that price though. I get why, but still – pivot + rack = lots of $

Gillis
Gillis
6 years ago
Reply to  Dude

My thought as well. A bit pricey for an extension. $200 would be a little more reasonable to me.

AngryBikeWrench
6 years ago
Reply to  Dude

Yup. I was really excited when I saw the headline, LOLed out loud when I saw the price. It’ll be worth it to many I’m sure, but not me.

Brandon
Brandon
6 years ago

You “laughed out loud” out loud? That made me lol.

AngryBikeWrench
6 years ago
Reply to  Brandon

Now I’m ROFLing out loud on the floor, literally.

Ish
Ish
6 years ago

I have been using the rak attach version all summer on my FJ cruiser with a 1 up usa 4 bike rack. It is bombproof and worth the price for full access to your trunk. The exhaust does heat it up but I have taken it on 6 hour road trips with no issues.

John
John
6 years ago

Mine on an Element melted the skidplate in the first drive. Otherwise it functions great! I’ll need to start looking at other exhaust tip options as well.

WilliamK
WilliamK
6 years ago

Better to have the exhaust hit the rack. A friend had his front wheel near the exhaust, when he got to the destination the wheel and tyre had deformed from the heat.

Bob
Bob
6 years ago

Have to question the clearance when entering/exiting roads and parking lots. My old Hollywood used to scrape a lot of places and this looks like it has even less rear clearance. Was a real issue around Asheville when up there to mountain bike.

Campervan owner
Campervan owner
6 years ago

This is a huge issue for anyone with a campervan carrying bikes. I need a swing away to access the storage compartment under the bed. I already have a tray style rack I like so this just solves the inconvenience of having to remove bikes all the time.

Bayard
Bayard
6 years ago

Finally a reason for sidepipes!!!

Mike Franke
Mike Franke
6 years ago

I love that you test-fitted this on my exact vehicle model, since I have the same limitation using my rack as you did. Thanks for that!

Mike Franke
Mike Franke
6 years ago
Reply to  Zach Overholt

Yes, yes there are. Also worth mentioning is that RakAttach does offer this device in a driver’s-side hinge version. Their pricing is higher than if purchased through Kuat, but if that exhaust issue is a concern, they offer that solution.

Joe Connell
Joe Connell
5 years ago

So, after a some road miles, how is the exhaust tip solution working on your Honda Element? Is rack holding up ok? Anyone tried other ides/solutions? I have two Elements and would love this issue to be solved!

Gary Schultz
Gary Schultz
4 years ago

Just picked one up today. No more climbing up on my rear tire to sit in the bed of my truck to put my gear on.

Kirk
Kirk
3 years ago

Just go with 1Up rakattach. You can order different sizes but also “driver’s side” swing if you need to avoid the exhaust.

Kirk
Kirk
3 years ago

For vehicles, like the one above, consider the cheaper option of a hitch extension of 6-12″. Much cheaper. While it doesn’t move the rack to the side (which is wanted, or needed, in some scenarios), it may allow you to fully open a tailgate or hatch without needing to pivot the bikes to the side.

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.