Home > Feature Stories

Bikerumor Lock-On Grip Roundup – Easton, ODI, Loaded, PRO, and Teva

26 Comments
Support us! Bikerumor may earn a small commission from affiliate links in this article. Learn More

Bikerumor Lock On Grip Round Up 005

Get a grip. OK, but which one? Today, fans of lock-on grips face a dizzying array of colors, styles, and patterns all screaming for prime placement on your bar. As we were cruising through Sea Otter, we thought it would be cool to pick up a few of the newest lock on grips from a variety of manufacturers to see how they stacked up both with and without gloves.

Bolt one on after the break.

Why Lock-ons?

Before lock-ons, grips were either glued or safety wired to the bar – that or they slipped. Today, grips like ESI’s silicone grips stay in place on their own without locking collars, but for anyone who prizes the ability to remove their grips quickly and easily(removing a shifter, changing bars, etc), lock-ons are tops. But with that convenience comes design challenges. The locking mechanism usually requires some type of plastic core which takes up valuable space which could be squishy rubber. Because of that, lock-ons tend to be thicker, or slightly harder for the thinner varieties – this is where the design can make a huge difference.

A word about hardware: Why does hardware even matter? I’ve seen plenty of stripped out 2.5mm lock on bolts in my time at the shop, so why do they still use them? Well, with the larger 3mm bolts they are easier to clamp down which also means they are easier to over-tighten and potentially crack your carbon bar. They’re also slightly bigger and heavier.You should always be using a torque wrench when installing carbon parts, and if so 3mm bolts are probably preferred for the simple fact that they are a little more forgiving of worn allen wrenches. If you have a set of grips with 2.5mm hardware, just make sure to clean out any mud or dirt inside the head of the bolt with a pick before you go to unscrew it as this is one of the leading causes of stripped bolts. A little grease on the threads at installation is a good idea as well.

Bikerumor Lock On Grip Round Up 004

ODI x Vans Collaboration

Judging by how quickly ODI was selling through the new Vans grip just after it was introduced, it seems to already be a hit. Chances are good that if you’re into bikes and somewhere between the age of 20 and 40, you’ve owned a pair of Vans in your time. The iconic waffle tread is now on a grip – molded right here in USA by ODI. Sold in red, white, and black in addition to the gum sole color shown at Sea Otter, there are plenty of options to match your ride.

Bikerumor Lock On Grip Round Up 013

Bikerumor Lock On Grip Round Up 015 Bikerumor Lock On Grip Round Up 014

The Van’s ODI grip features a reinforced section on one side that you can place where you put the most pressure on your grip. Like other ODI lock-ons, the Vans grips use two 2.5mm allen screw clamps with plastic snap caps that snap into the lock collar. ODI’s Vans grip seemed to be equally good both with and without gloves, but it was without gloves that it was most surprising. Above all, these grips have the cool factor that would probably make these a hit, even if they weren’t as good as they are.

ODI Vans Grips are available in 4 colors for $29.99.

Measurements:

  • Length: 135mm
  • Thinnest point: 30.0mm
  • Thickest point: 33.0mm
  • Weight (set w/all hardware): 109g

Highs:

  • ODI Made in the US quality
  • Tenacious grip
  • Never lose a collar

Lows:

  • 2.5mm screws are prone to filling with mud, potentially causing them to strip if not completely cleaned out before removing

Bikerumor Lock On Grip Round Up 012 Bikerumor Lock On Grip Round Up 011

0627_5337

PRO Tharsis Grips

As the oldest grip in the line up, the PRO Tharsis grips are also the most unique. Not only do the Tharsis grips offer an ergonomic-but-but-still-mostly-round shape, but they also have their own locking system. In addition to the standard clamp nearest the shifter with a 3mm Ti allen screw, there is also a 3mm Ti allen in the very end of the grip which when tightened, squeezes a blue elastomer against the inside of the handlebar. This is a very carbon friendly design, but not one without problems – after having the grips installed for awhile, the elastomer got stuck inside the bar. This meant I had to take the whole system apart, take the opposite grip off as well, and punch the elastomer through to the other side. It hasn’t happened on all the handlebars, but it did happen.

As mentioned these were certainly the most ergonomic in the group, but not to the point where you feel you can’t really rotate your hands around the grip. I have to say I’m not a fan of the outside of the grip tapering to the inside, if anything, I would prefer the reverse.

PRO Tharsis grips are available in Black or White.

Measurements:

  • Length: 137mm
  • Thinnest point: 29.0mm
  • Thickest point: 31.0mm
  • Weight (set w/all hardware): 118g

Highs:

  • Ergo design without being cumbersome
  • Carbon friendly

Lows:

  • Not as durable as the rest
  • End clamp can be fiddly

Bikerumor Lock On Grip Round Up 007

Bikerumor Lock On Grip Round Up 009

Loaded AmXc NoSlip Grips

Certainly one of the most eye catching grips on test is Loaded’s AMXC NoSlip grip. With looks that cross between Rhino lining and grip tape, The AMXC grips offer a seemingly random pattern of ridges for grip. Built with their no slip rubber, and alloy lock rings and end caps, the AMXCs lock in place with dual 3mm allen screws.

Honestly, with the name and the design, I really expected these to be more grippy especially when wet. Due to our humidity around here, grips get wet pretty quickly just from sweat so these grips are probably better suited to drier climates. The comfort was there, but they seem to work better without gloves as well.

Loaded AMXC No Slip Grips are available in Red, Blue, Green, Gold, and Black for $29.99.

Measurements:

  • Length: 135mm
  • Thinnest point: 30.0mm
  • Thickest point: 34.0mm
  • Weight (set w/all hardware): 119g

Highs:

  • Locking clamp and end cap bling
  • Unique look
  • Comfortable
  • 3mm bolts

Lows:

  • Not as grippy as you may think

Bikerumor Lock On Grip Round Up 006 Bikerumor Lock On Grip Round Up 008

Teva PedalLINK Grips

Another shoe inspired grip? Yup. Inspired by Teva’s PedalLINK outsole of the Links and Pivot shoes, Teva had these grips at Sea Otter. No word on availability, but if our impressions are any indication they’re worth putting out. The PedalLINK is the thickest in our test at the grip (not the clamp), which means it’s also the softest – which is good, but super soft grips tend to wear out faster. With a single 3mm locking bolt and collar, the Teva grips still held in place without any twisting. I’m typically a fan of thinner grips, but the Teva could change my mind. Equally good with or without gloves.

Teva had the grips in black and Teva Blue, but no word on if they will be offered for sale.

Measurements:

  • Length: 134.4mm
  • Thinnest point: 31.4mm
  • Thickest point: 33.8mm
  • Weight (set w/all hardware): 112g

Highs:

  • Solid locking with only one collar
  • Super soft
  • 3mm bolt

Lows:

  • Not available yet
  • May wear out faster than others

Bikerumor Lock On Grip Round Up 003 Bikerumor Lock On Grip Round Up 002

Bikerumor Lock On Grip Round Up 018

Easton Lock Ons

Easton’s new grips have admittedly already gotten a lot of press from us, as Marc and I unknowingly double posted them already. The slime green Easton grips have been in the rotation for awhile now, and are the slimmer 30mm grip design. The same grips are also available in 33mm diameters for a thicker grip. One of the biggest changes to the Easton grip is one you can’t see which is the use of elastomeric polyurethane instead of Kraton rubber. The claim is the same feel but drastically improved durability.  The Easton grips have a thicker side to place under your palm, a side with raised smaller Easton logs for increased finger grip.

Bikerumor Lock On Grip Round Up 019 Bikerumor Lock On Grip Round Up 016

The other big difference is the use of flaps that cover both of the lock collars. The flaps are two fold – they give your some grip material instead of metal on the ends of the grips acting somewhat like moto grips with flanges, and they protect the 2.5mm allen screws from dirt and debris. Unlike the other grips that have a cap that snaps into the lock collar, the Easton’s end cap is one piece with a carbon friendly clamp. The only downside to the design, is it appears to be easier to knock off the bar. After smashing the end of my bar into a tree, the end cap went bouncing down the trail. To be fair I was rushing to get the grips installed in the parking lot, so make sure to check the torque when you install the grip.

Easton Lock On grips are offered in black, blue, red, orange, Neon green, and white for $25.00.

Measurements:

  • Length: 138.2mm
  • Thinnest point: 30.0mm
  • Thickest point: 36.0mm
  • Weight (set w/all hardware): 105g

Highs:

  • Awesome grip, wet or dry, gloves or bare hands
  • Surprisingly soft for a thin grip
  • Longest in the test, and also the lightest
  • Great control

Lows:

  • Raised shoulders may not be for everyone
  • Clamp may not be as secure as the rest
Bikerumor Lock On Grip Round Up weight
Weight of the Eastons was later verified on the Feedback Scale

Editor’s Choice:

It’s hard to narrow down a perfect grip in a sea of options, but in this group of five the Easton was the grip that is still on my bike. Soft while keeping it thin, grippy in all conditions, solidly locking, the Eastons are well thought out all the way through. After all of the testing was finished, and then after a 4+ hour ride a simple wipe down of the grips left them looking like new. Some grips I like, start to wear after the first ride. I know there will be some that don’t like the raised ends, but the grip is longer than the rest offering plenty of room in between. They even get a nod from the retail point of view with a low price, and smart packaging so the customer can “feel” the grips. If you don’t mind the moto feel, these are up there with the best grips around.

Subscribe
Notify of
guest

This site uses Akismet to reduce spam. Learn how your comment data is processed.

26 Comments
Oldest
Newest Most Voted
Inline Feedbacks
View all comments
Rivers
10 years ago

I am surprised at the loaded grips…I was expecting them to be gripier. I really like the look of the easton grips, don’t know if I would like the flange or not…gotta test them. I have been running a set of Chromag Palmskin grips and love them….check them out as well…love the endcap design.

jorge
jorge
10 years ago

guilty as charged, I have never tested other lock on grips other than ODI. Some other brands here and there, but never really owned other brand of grips.

ODI is the real deal! If you’re careful you won’t strip the bolts (I have stripped a few to be honest), you can customize them, they offer A LOT of patterns, and they are overall the best grips on the market!

Try the Cross Trainer pattern, which is a modified ribbed (mushroom) pattern in criss-cross. THE BEST! I’ve seen cross country pros using them.

the X-treme pattern is good as well, and you really can’t go wrong with the classic Ruffian if you’re into thin grips.

My 2 cents.

Yoshi
Yoshi
10 years ago

ESI Silicone – the lightest best feeling out there.

LilJoe
LilJoe
10 years ago

Race Face Half Nelson. That is all.

Chasejj
Chasejj
10 years ago

Ergo GP1. I really cannot see myself ever using anything else.

Jack
Jack
10 years ago

Why is Ergon not here??

GP3 Biokork grips!

captain derp
captain derp
10 years ago

deity’s lock on grips are surprisingly nice as well.

Earth Rocker
Earth Rocker
10 years ago

ESI grips nuff said…

Nick
Nick
10 years ago

ODI PEATY!

Cheers!

gonna order a pair of the Vans collab, though, those look sweet!!!

Jason
10 years ago

+1 for the RaceFace Half Nelsons.

Thin, sticky, light, and cheap!

Bob
Bob
10 years ago

On the topic of gloveless riding: I ride exclusively without gloves, and a huge issue on longer, sweatier rides is that sticky grips begin to rub your hands raw. I’m continually surprised no one else seems to have this problem: even the slightest stickiness in a grip leaves my palms raw on any ride longer than an hour or so.

There are tons of options for non-sticky tape for road bikes (foam, cork, fake suede), but I’ve only found two non-sticky mountain bike grips that work at all: Ritchey and Specialized foam grips. The Ritchey is marketed as retro, and the specialized is supposed for superlight XC types, but they’re the only grips I can ride all day without gloves.

mellon
mellon
10 years ago

Five pairs of grips is not a ‘Round Up’. A round up would be you guys rounding up all the grips in the category. You didn’t do that. You just reviewed some grips.

Ruadhrigh
Ruadhrigh
10 years ago

For the next “Round-up” get the Renthal lock-ons.

Tes
Tes
10 years ago

I have big hands and piano fingers, so it looks like I’ll need to stick with my ODI Rogue and derivatives like Race Face Strafe. Or maybe the thick version of those Eastons are fat enough…

Joe P
Joe P
10 years ago

I have large hands xxxl or size 12. Single clamp at the inner portion of the grip is fine for me as the outer palm of my hand hits on an outer clamp if there is one. I have used Specialized and Bontrager without issue and no slippage at all.

The PRO Tharsis have always intrigued me but for now I have no need to replace grips but in the future I might look at those as well.

JB
JB
10 years ago

I always seem to come back to my OURYs…. they wear out quick, but damn are they comfy, even the lock-on ones.

Mike
Mike
10 years ago

RaceFace Half Nelsons baby! Nothing better than deathgripping a topo map of Whistler!

JD
JD
10 years ago

I just got a pair of the vans grips, I love them but they dont grip when wet without gloves.
I won a pair of the teva grips last year but they were a tad too thick for me.
I run sensus grips on my DH bike and my DJ bike.
I just put the vans on my trail bike and they are dope.

Johan
10 years ago

Guys who ride these narrow grips must have hands very different from mine.
Perhaps they only do very short rides?
Love Ergons or perhaps ESi Extra chunky.

NASH
NASH
10 years ago

It you get a one of those plastic yokes stuck in your bars the best bet is a wine bottle opener and a spray of WD40. Had this on BMX bars when poking through is not an option.

Daver
Daver
10 years ago

+1 for the Ergon GP1.

but i am keen to try out the new Hope lock on grips, they look to be a great solution to having the lock on collars digging into your hands if you ride with your hands on the end of the bars as i do. and made right here in the UK, home of all that is great!

mofo
mofo
10 years ago

ESI Chunky – best grips I’ve ever used!

Gillis
Gillis
10 years ago

They aren’t lock-ons, but I can’t ride anything but the legendary Yeti Speed Grips.
http://www.odigrips.com/yetispeedgrips.aspx

David French
David French
10 years ago

Interestingly, when you buy the end caps for ODI on their own, they say made in Taiwan on the packaging.

chris a
chris a
10 years ago

ESI Grips!!!!!

Word.

sillybike
sillybike
10 years ago

ESI .

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.