Home > Bike Types > Cyclocross

EB13: Formula 35 Suspension Fork with New Internals, Massive Adjustability – Plus Road Hydro Brakes

6 Comments
Support us! Bikerumor may earn a small commission from affiliate links in this article. Learn More

2014 Formula 35 suspension mountain bike fork

The new Formula 35 fork gets them into bigger wheel sizes.

Their 33, which we reviewed here, is only for 26″ wheels. The 35 will be available for 650B and 29er, with travel set at 100-160mm and 100-140mm respectively. Travel is internally adjustable in 10 and 15 millimeter increments with internal spacers. You’ll have to pull the lowers, which means the oil bath that lubricates the sliders will have to be refilled, but they say it’s an easy adjustment. You’ll be able to order it at whatever length you want, though.

What’s particularly impressive is the wide range of adjustability – everything from the expected compression and rebound down to the position of the adjustment knobs is up to you…

2014 Formula 35 suspension mountain bike fork

The crown and arch is heavily shaped.

2014 Formula 35 suspension mountain bike fork

The cartridge unit is new and uses an expanding rubber bladder reservoir rather than just pushing the oil into the top part of the cartridge like the 33. Sales & Tech Support Manager Jeff Stoudt says this improves small bump sensitivity.

2014 Formula 35 suspension mountain bike fork

It has a massive amount of adjustability, with compression, threshold and lockout controls on the top.

2014 Formula 35 suspension mountain bike fork

Rebound is on the bottom, and that knob pulls out to provide the tool for the threshold control.

The top cap with the controls will rotate by loosening a set screw. This serves two purposes: it allows OEM customers to position the lockout knob so it doesn’t hit the crown, and it lets the end user rotate it so the lever is exactly where it’s easiest for them to use. Even better, the threads on either side of the fork are the same, so you could switch the damping cartridge to the left side of the fork and the spring stack to the right. If you wanted. Stoudt says you can do it in about five minutes, including replacing the oil.

Speaking of oil, they use Ballistol Oil (commonly found in hardware stores internationally), and by adjusting the amount in the air chamber, you can fine tune the spring rate. More oil makes it more progressive.

The cartridge uses a Directional Floating Seal (aka cup seal, similar to what’s used on their master cylinder pistons). As it compresses and oil pressure builds, it bulges a bit to provide a tighter seal. It’s a tiny lip, though, so it’s not adding noticeable friction.

Not shown, they offer a hydraulic remote lockout that’s better than what’s offered on the 33. Instead of replacing the entire top cap and losing the compression damping controls, it simply hoses into the lockout lever hole and lets you keep the other controls.

2014 Formula 35 suspension mountain bike fork

Two thru axle options are available. Shown above is the standard, tooled version.

2014 Formula 35 suspension mountain bike fork

Or, if you don’t mind an extra 26g, there’s a QR lever version that provides a big lever to tighten the axle down by spinning it in until it’s close, then closing the lever. The trick part is that you can slide the lever out, and its shaft has a standard hex shape and a 12-sided hole so you can slide it back in at virtually any angle you like. No more levers sticking randomly forward or down.

Claimed weight is 1650g for the 650B and 1700g for the 29er, both with uncut tapered steerers and no axle. Stoudt says on the samples he’s received, once the steerer is cut and the axle’s in place, they’re coming in lighter than claimed. We’re hoping to test that claim with a review unit this fall.

FORMULA RR1 Di2 ROAD HYDRAULIC DISC BRAKES

2014-Formula-RR1-Di2-road-bike-hydraulic-disc-brakes01

We snapped this pic at Crankworx with a promise to get back to you with more info. Unfortunately, the story’s not as good as we’d hoped.

The RR1 will only work with first gen Dura-Ace Di2 10-speed, not the current E-Tube groups. Bringing it up to date isn’t likely a project they’ll tackle now that Shimano has their own full hydraulic system. They will, however, continue to develop their Campy road hydraulic brake setup to some extent, but they’re waiting to see how they can work out warranties on the shifting parts since they don’t fully control those parts. The system developed for Colnago is still exclusive to them and led that project, so Campy was involved with parts of that system. All those factors would have to come together again under Formula’s guidance for a standalone EPS brakset to be developed. We’ll keep you posted.

Subscribe
Notify of
guest

This site uses Akismet to reduce spam. Learn how your comment data is processed.

6 Comments
Oldest
Newest Most Voted
Inline Feedbacks
View all comments
Nony B.
Nony B.
10 years ago

I just hate it when forks require a special tool to remove the damper assemblies. Why can’t Formula just use a simple hex like Fox, RockShox and most fork manufacturers do?

rigel
rigel
10 years ago

Looks like a standard 12 point will do the job… It does not say it requires a special one.

greg
greg
10 years ago

it looks to me like itll take a standard 12pt socket…

Dave
Dave
10 years ago

greg – It looks like you’d be able to use a 12pt socket in a pinch, but you’ll definitely chew up the cap. Rather like using an allen wrench in a torx bolt: for emergencies only.

Sardinian Rider
Sardinian Rider
10 years ago

If their fork perform the same way their brakes do imma buy a Walmart bike and slap that fork on my Stumpy FSR,it’s a sure bet.

Mitch Conner
Mitch Conner
9 years ago

I just saw these forks at the Sea Otter and I was really impressed. The guy there said it takes a regular 28mm socket to remove the damper and the cartridge has regular wrench flats for easy overhauls. I would know the first thing about rebuilding a cartridge but I think it’s cool they did that. If it works as well as it looks I think they nailed it!

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.