Home > Bike Types > Commuter

Loop Wheels Curl Carbon Fiber Loops into Suspension Inside the Wheels

33 Comments
Support us! Bikerumor may earn a small commission from affiliate links in this article. Learn More

Loop Wheels carbon fiber spring suspension bicycle wheels prototype

Spotted at the Bespoked, UK’s handmade bicycle show, Loop Wheels should be getting things Kickstarter’d this week for their carbon fiber looped bike wheels. Details are pretty scant, but the obvious is the composite looped spokes that create  three sets of springs between the hub and wheel.

The design most likely requires a drum or disc brake since the rim’s position would likely change too much for rim brakes. We’re thinking this could be a fun design for commuter and city bikes where aerodynamics and weight are slightly trumped by comfort, particularly where the streets are a bit rough. More info as it comes online, and another pic after the break…

Loop Wheels carbon fiber spring suspension bicycle wheels prototype

Thanks to Jon C. for sending these pics in!

Subscribe
Notify of
guest

This site uses Akismet to reduce spam. Learn how your comment data is processed.

33 Comments
Oldest
Newest Most Voted
Inline Feedbacks
View all comments
Androo
Androo
10 years ago

Yeah, I think that’s definitely a neat idea. Depends on how well it works, though. And how much it weighs. And how much it costs.

If it offers a lot of suspension travel than it has potential, but if it’s only a little bit, then one has to wonder why they didn’t just upsize the tire and lower the pressure a bit.

stodr
stodr
10 years ago

I don’t think it would affect the brake track. The wheel would flex on the bottom but would return to original shape and diameter when it rolled far enough to not be in contact with the ground. If it did not return to original shape or size after the flex the ride would be really crappy.

iperov
iperov
10 years ago

shut up and take my money!

Ck
Ck
10 years ago

I’m intrigued. Definitely needs a disc brake setup.

comrade
comrade
10 years ago

how is the low / high speed compression and rebound damping?

seramik
seramik
10 years ago

that reminds me Tioga Disk Drive Rear Wheel

MMyers
MMyers
10 years ago

I was gonna make a snarky remark about damping, but if that setup provides <1.5" or so of suspension on a commuter bike, it's probably a good thing.

Clever idea, at least.

Undamped Manitous were the sh!t, back in the day. Just sayin'

Max
Max
10 years ago

With every rotation the springs will bend and absorb a amount of energy. Normally this is called “damping”. Its pretty useful in some cases. But it’s pretty unusual to damp a rotation of wheels, because this will slow down the straight moving. For Bicycles (and all other vehicles) you should mount your springs in the direction where the impact is coming from plus a additional damper to stop the bouncing of the spring.

Anway, WHOOOO it’s fancy Stuff out of Carbon WANT!!!! Take my Money (and brain)!

David
David
10 years ago

I would like the Lucite fork too, so then I can see when it breaks apart.

Hmmmm
Hmmmm
10 years ago

OK, so this would feel weird, as as the ‘suspension’ compresses, your pedalling torque curve would change due to the wheel changing shape….??

Ventruck
Ventruck
10 years ago

literally attempting to reinvent the wheel. My word.

Dan
Dan
10 years ago

Seconding how compression and rebound get adjusted… Also how will it handle/shed mud? looks like lots of nooks and cranies for mud and debris to hide and cling… I don’t even want to start thinking about what kind of aero properties these bad boys have, … High on my list to try, if I every had the opportunity (’cause dang I’m curious) but low on a buy until the applications for this type of wheel are nailed down.

Watchtower
Watchtower
10 years ago

“I see you have constructed a new carbon fiber suspension wheel. Your skills are complete.”

Luker
Luker
10 years ago

Lateral stiffness?

Brandon
Brandon
10 years ago

It had better not deform too much or the bead of the tire will blow off….

ChrisC
ChrisC
10 years ago

Looks to me like it is a rigid rim and all the suspension takes place within the three loops of carbon inside. No worries about wheels changing shape or tires blowing off. The axle just moves off center during compression.

ChrisC
ChrisC
10 years ago

Torque wind up might be a real issue though, so even dusc brakes might not work…

ChrisC
ChrisC
10 years ago

*disc

jimmythefish
jimmythefish
10 years ago

This looks dodgy. As per above – lateral stiffness? You have what looks like three contact points spot welded to the rim. I like my rims to stay somewhat connected to the hubs. These look like they have potential for rather catastrophic failure.

Also – why run the valve stem right through one of these three contacts?

Bob McNaughton
Bob McNaughton
10 years ago

Can’t tell if trolling or legitimate product.

I don’t see how they could maintain torsional stiffness under braking… And that falls into the “bad” category.

Mindless
Mindless
10 years ago

Worst idea ever.

Gillis
Gillis
10 years ago

It looks like the hubs have internal drum brakes. They both have little black levers on the outside. And you can clearly see a cable running down to the rear hub.

The way the loop-ends overlap each other, it looks like that would give some lateral stability.

It is curious as to why they put the valve stem in the middle of a loop and not between.

Ham-planet
Ham-planet
10 years ago

I used to think that URT suspension and suspended seatposts were the worst ways to implement suspension on a bicycle.

Thank you for opening my mind, Loopwheels!

gringo
gringo
10 years ago

looks like the idea could be refined a bit in the direction of this Military version with an airless tire…flat proof and comfortable commuter tire would be sick.

Daver
Daver
10 years ago

BOOOIINNGGGG! like riding a loaded catapult.

Luiggi
Luiggi
10 years ago

The rim won’t bend or suffer from any deformation. Just the hub will move relatively to it.

Ryan
Ryan
10 years ago

Quite refreshing to see such a new solution.

Nash
Nash
10 years ago

Have fun on the corners at speed.

ant1
ant1
10 years ago

there is not way i’m putting a set of these on my P5.

g
g
10 years ago

@Ryan – “new solution” to what problem?

i'd like to see some comparisons
i'd like to see some comparisons
10 years ago

on flat ground due to the hub always being nearer the ground than the top of the wheel, all three “loops” have to flex and return for each revolution of the wheel, meaning it would be like going up a gentle hill all the time (work wise)? (unlike conventional suspension that will flex due to riders weight and stop regardless of revolutions.

This is just something i thought of the instant i saw these, they do look fun though but if indeed they do feel like your “going up hill” all the time they’d have to be VERY fun to be worth the extra effort. I guess for crazy obstacles??

i’d like to see side by side freewheel tests for riders, i think they might be radically less efficient than regular wheels (more comfy maybe :).

Ronnie
Ronnie
10 years ago

Wonder what it would do on an Experimental Mini Max airplane….???? Hmmmmmm

swapnil dighe
swapnil dighe
5 years ago

which composite material is used for suspension spring in this loop wheel?

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.