Home > Bike Types > Commuter

NAHBS 2013: Ti Cycles Full Suspension Fat Bike, Innovative Electric Cargo Bike & Hydraulic Brake Line Coupler

8 Comments
Support us! Bikerumor may earn a small commission from affiliate links in this article. Learn More

Ti Cycles Full Suspention Fat Bike

Dave Levy of Ti Cycles has been building bicycles since 1986.  That experience really shows in the bikes Ti Cycles showed at this years NAHBS.  Dave is a very qualified engineer, and one of the biggest bike nerds I know.  One look at his full suspension fat bike and you will see what I mean.  One look however, is never enough with any of Dave’s Bikes.  And since I know you are all wondering, the full build comes in right at 32 lbs.

Power through for all the technical details details on the fat bike, plus one of the most innovated cargo bikes on the planet.

Ti Cycles Full Suspention Fat Bike Lefty Fork

Ti Cycles Full Suspention Fat Bike Lefty Adapter

Up front, the bike is running a Cannondale Lefty set to 80mm of travel.  It’s attached to the bike via Mendon Cyclesmith adapters.

Ti Cycles Full Suspention Fat Bike Linkage

The rear shock is set to 2.5 inches of travel, and the rocker plates ride on six sealed bearings.  Ti Cycles considers this a 4 inch suspension system overall thanks to the give in the giant tires.

Ti Cycles Full Suspention Fat Bike Flex Stay Yoke

No lower pivot is used.  Instead, Dave is makes use of his Flex Stay yoke.  This also helps to add a fair bit of lateral stiffness to the rear end.  That stiffness is aided by a 142 x 12 through axel.  It’s not often you see an FSA K-Force crankset on a fat bike either.  Dave has figured out over the years how to lengthen (and shorten) spindles using a proprietary technique he would not disclose, allowing him to use any crankset desired.

Ti Cycles Full Suspention Fat Bike Top Tube Graphics

As you may have guessed already, this bike was handbuilt in the lovely city of Portland Oregon.

Ti Cycles Full Suspention Fat Bike Corduar Rim Strip

To keep things matchy matchy, an orange strip of Cordura plus some packing tape like material were used instead of a standard rubber rim strip.  The wheel build is a bit unconventional as well.  Ti Cycles used a standard 135 spaced hub and a 34mm spacer on the left side.  The chainline is straight, and on my short test ride, the bike shifted great.  This is a great set up because it makes use of much easier to find parts.

Ti Cycles Cargo Bike

Once upon a time, Dave Levy lived, worked, and played in Seattle, WA.  He had a car free lifestyle.  Currently, he resides in Portland, OR on some acreage that is home to both his residence and his shop.  The location is up in the west hills, and the automobile has become a staple in his life.  The above cargo bike came about in an effort to go back to a car free lifestyle.  The engineer in Dave really came through on this build.

Ti Cycles Cargo Bike Electric Motor

Because hills are a pain to climb riding a monstrosity such as this one, an electric motor made it’s way into the specs list.  This one is from Ecospeed, and has an output of 1300 watts.  It also features a cruise control mode that lowers the output to 200 watts and only operates in an assist mode.  This allows for 20mph at 60rpm.

Ti Cycles Cargo Bike Drive Side Belt

This bike has 100% more belt, thanks to a Gates Belt Drive for both the electric motor and the crankset.  The front half of the drivetrain is an FSA Metropolis (Patterson 2 speed) set up.  Dave also made use of part of the mid shaft setup from Todd Schusterman (Davinci Tandems) to connect everything up front for maximum efficiency and helping to maximize battery life.

Ti Cycles Cargo Bike Alfine Rear Hub

The rear gets a Shimano Alfine 11 speed hub.

Ti Cycles Cargo Bike Cargo Box

A lot of thought went into redesigning the traditional cargo box.  Space is typically lost up front due to the steering linkage.  This bike is designed with two head tubes and three headsets, as well as a custom steering linkage that goes all the way under the box and up the front non-drive side tube of the box frame.  This helps maximize the cargo space.

Ti Cycles Cargo Bike Fork

A generator hub keeps power going to the Light On light.

Ti Cycles Cargo Bike Cable Routing

A clean cable routing solution.

Ti Cycles Cargo Bike Rear View

Around the back is a long tail rack ready to carry goods or people.  The rear wheel is 24″ for added strength.

Ti Cycles Cargo Bike TPR Rear Disc Brake

Ti Cycles Cargo Bike TRP Brake Lever

To bring this beast to a halt, stopping power is provided by TPR in the form of a pre-release version of their new 4 piston downhill hydraulic disc brakes.

Ti Cycles Cargo Bike Hydraulic Adapter

Because there are no stock hydraulic hoses long enough to accomodate a build such as this one, Ti Cycles created a universal hydraulic line coupler that can be used with either DOT4 or mineral oil.  These should be available soon for purchase.

Ti Cycles Cargo Bike Macallan Holder

Pedaling motivation provided by Macallan.

Subscribe
Notify of
guest

This site uses Akismet to reduce spam. Learn how your comment data is processed.

8 Comments
Oldest
Newest Most Voted
Inline Feedbacks
View all comments
Mark M
Mark M
11 years ago

I want both bikes! Nice engineering.

joby
joby
11 years ago

10yr? Sheesh, at least gimme a 12 year or cask strength….let alone an 18yr.

gringo
gringo
11 years ago

I suppose we all have a Granddad or uncle who is missing some fingers due to a farm or industrial accident back in the pre- OSHA days.

This cargo bike will insure that our offspring will also have uncles or moms missing a digit or two….that thing is SCARY!

Nash
Nash
11 years ago

So how long does one of those Flex Stay yokes last?

ABW
ABW
11 years ago

@Nash – longer than the average set of knees or hips. Don’t worry about it…

The Goats
11 years ago

Super bikes and great to see the freedom enjoyed by Dave to really build out bikes to the limit. His road bikes while simple and elegant looking are also exceptionally engineered.

Great stuff!

XOXO

Goats

Eric
Eric
11 years ago

BOTH BIKES = LOADS OF FUN!!

Thomas Weber
Thomas Weber
9 years ago

Jagwire makes hydraulic line kits with 3000mm length. It will reach the front of a cargo bike, as seen on the bullitt cargo bike. Available for any brake system and in multiple colors. No line coupler needed.

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.