Home > Reviews

Fox Float Air Volume Spacer Kit: Installed and Reviewed

10 Comments
Support us! Bikerumor may earn a small commission from affiliate links in this article. Learn More

The fox kit comes with three different spacers and a packet of float fluid. The volume change for the plastic spacers is .2, .4, and .6 cubic inches.

There’s a difference between visiting a bicycle at a shop, playing with it in the parking lot, and living with it. Once a frame finds it way into your garage and your heart and you’ve had time to develop a relationship with it, you begin to learn it’s little eccentricities. My best friend, a Transition Double, is a great bike. From the onset I knew that it wasn’t going to be the best climber but its playful nature suits my riding style perfectly.

What I gradually came to understand as our relationship unfolded, is that we didn’t always see eye to eye on rear suspension performance. The single pivot rear end just felt too linear. When the rear shock was set up for my smooth bermy local trails, the jump oriented bike felt great, but over sharp stutter bumps or on big hits – the shock would bottom out harshly.

So how did my bicycle and I resolve our issues?

How to Install the Spacer Kit

Step One: This the most important step for safety reasons!  Release all the air from the canister by depressing the Schrader valve. Then gently cycle the shock and mount the bicycle securely to the stand. Position the shock so that it is horizontal(ish) to the ground.

Step Two: Unscrew the air can by firmly turning the canister clockwise and slide it midway down the shock body. You don’t need to push it very far down to insert the spacer.

Step Three: Look under the head of the shock for a steel washer and O-ring. On some bikes there may already be an air-volume spacer in place. Slide the washer down the shaft as pictured. Remove the stock plastic white spacer if necessary.

Step Four: Slip the spacer over the washer with the carved side facing down until it snaps into place.

Step Five: Push the spacer, washer, and o-ring up into the shock head.

Step Six: Supporting the weight of the rear suspension, gently ease the can up to the shock head, and turn it clockwise to tighten. Firmly hold the can while tightening until it is snug before releasing. Otherwise, the negative pressure could be enough to slam the can into the shock head, tear out the threads, and damage your shock.

Step Seven: Inflate your shock and test ride!

Ride Impressions

Wow. The Float Air Volume Spacer Kit retails for only $25 USD, but it is one of the single biggest improvements to a bicycle I’ve ever made. The spacer reduces the volume of the air canister, which causes the shock to ramp up faster, and feel significantly more progressive.

By changing the air spring compression ratio, you can reduce the amount of air pressure required in the shock, which finally allowed me to set the proper suspension sag. In order to prevent harsh bottom outs in the past, the shock required 15-20 PSI more air than it does with the spacer, which compromised the small bump compliance. A switch from no spacer to the .4″ spacer increased the compression ratio of my shock from 3.0 to 4.0.

This simple modification can easily be performed by a competent tinkerer and offers a pretty big improvement at a very marginal cost. Fox does note that same compression ratios are too high to safely use and  “the resulting compression ratio…. combinations is beyond the bounds of product user safety. With a spike of excessive air pressure, the air sleeve can suddenly fail and cause a crash, property damage, SERIOUS INJURY, OR DEATH.” The full list can be found here.

 

Subscribe
Notify of
guest

This site uses Akismet to reduce spam. Learn how your comment data is processed.

10 Comments
Oldest
Newest Most Voted
Inline Feedbacks
View all comments
Typee
Typee
11 years ago

Did this to my RP23.. really does work wonders! If you have a Fox Float shock, you can’t afford NOT to get this little wonder kit! Next best thing to having it “PUSHed”

Mr. P
11 years ago

I agree. 15 minutes & $25 for the kit, turned my great bike to stellar.

P

Steve M
Steve M
11 years ago

Killer idea. Stratos had something similar 15 years ago but not as user friendly.

Radiant Ultralord
Radiant Ultralord
11 years ago

I would think a reputable frame manufacturer would make sure their shocks are set up properly out of the box with the best air volume etc.

Mr. P
11 years ago

@Radiant Ultralord
It’s tuning to personal preference. On my Enduro, some users like to blast through boneyards, while I need more progressiveness for landing airs. The progressiveness sacrifices some plushness in the rough. What works best for me does not necessarily work best for others. I’m ok with a fine tune tweak.

P

dave
dave
11 years ago

can’t you just put some extra oil in the sleeve to take up space?

Mr. P
11 years ago

@dave No. Adding oil for volume control can degrade a shock’s performance.

http://forums.mtbr.com/turner/dw-5-spot-rp23-mod-503070-10.html#post9678595

P

Andrea
Andrea
9 years ago

Hi,
does this tuning (spacer adding – reduction of air volume) affect somehow the prodepal behavior (making it work less firm)?
Thanks

Filip Andersson
Filip Andersson
6 years ago

Do you guys think i can use double spacers in my float x rear shock. Im kinda heavy and need more spacers since im om 265 psi and still go through alot. If i go 280 psi the shock feels too stiff. Thats why im thinking of going with two spavers and reduce psi to about 245.

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.