Home > Bike Types > Mountain Bike

Quick Review: Fox Digital Shock Pump

16 Comments
Support us! Bikerumor may earn a small commission from affiliate links in this article. Learn More

Fox Digital High Pressure Shock Pump review

The Fox Digital High Pressure Pump debuted at Interbike last fall and alongside the prototype iRD suspension set up app/shock combo. Quite simply, it’s a high pressure shock pump with a digital pressure gauge that makes it far easier to get super accurate air pressure in your fork and shock.

The readout shows air pressure in PSI and BAR in tiny increments (0.5psi below 100psi, 1.0psi increments over 100psi), letting you fine tune the pressure. The pump’s body is durable alloy with a 360º rotating hose. Stroke is nice and smooth. It’ll pump up to 300psi, which should satisfy the needs of any modern suspension component.

UDPATE: Comments about accuracy and tolerances from Fox’s engineer added at bottom!

Retail is $69.99, available now. More pics below…

Fox Digital High Pressure Shock Pump review

Instructions? You don’t need no stinkin’ instructions. What you see is what you get. All that print on the inside of the box is just FCC and CE disclaimer jargon.

Fox Digital High Pressure Shock Pump review

The hose rotates very freely, which makes it incredibly easy to hold the pump in a natural position. Yes, $70 is a bit much for a shock pump, but if you use one a lot like we do, having that extra bit of accuracy and easy to read numbers is a real treat.

From David Crum, Fox’s engineer for such things:

The gauges in the digital pumps are calibrated at the factory. In our testing, they show next to no drift in their readings over many hundreds of uses. It is important to note that these gauges, while highly repeatable – each gauge will read quite accurately the same known pressure and display the same value each time – are not able to achieve lab levels of accuracy. When compared to a calibrated master gauge, the gauges in the hand pumps will have some variation.

If perfect accuracy is required from a digital gauge, there will be three factors which prevent it from being selected for a hand pump:

  1. Cost – lab quality gauges (+/- 0.5% or better) start at a few hundred dollars US – and that’s just the gauge without a pump attached.
  2. Portability – most lab quality digital gauges require more power than a small battery can supply, often they are either 24 VDC or 110 VAC.
  3. Size – the pressure sensors and control electronics required by lab gauges prevent the gauge from being small enough to fit on a lightweight hand pump.

He concurred with the comments regarding accuracy and repeatability and recommends using the same pump all the time, which means once you find the setting that works for you, repeating that pressure with the same pump yields the same result whether it’s 100% accurate or not.

Subscribe
Notify of
guest

This site uses Akismet to reduce spam. Learn how your comment data is processed.

16 Comments
Oldest
Newest Most Voted
Inline Feedbacks
View all comments
Pete
Pete
11 years ago

I really wonder how accurate this will be. Across three of my shock pumps, of the same brand and model they would read 5-10psi differently. Putting a digital readout on an inaccurate measuring device just serves to convince the gullable it’s reading accurately.

To read to 0.5psi increments it’ll have to be pretty well made internally, between a $70 price and low volume production I can’t imagine this is so sophisticated.

I’d like to see a lab test across ten of them.

Andy
Andy
11 years ago

The key to setting up your suspension is to use the same pump all the time. This way any inaccuracy between pumps is negated because 175psi (just an example) is correct for your pump and shock. I apply the same philosophy to tire pressure. It’s all relative to your pump.

Bill C
Bill C
11 years ago

Gauge aside, it’s good to see that Fox is using the same shock pump as everyone else- those things last more or less forever…

gringo
gringo
11 years ago

+1 for Andy,

true accuracy is not as important as consistency.
always use the same pump and you will be fine.

Detlef
Detlef
11 years ago

@Andy: Normal pumps have high tolerances, so even if you use the same pump you will have high inaccuracy. Different ambient temperature and other factors will influence the measurement if the gauge has no compensation.
After all, it’s pretty senseless to show two decimal places, when no range of tolerances is given.

Bob
Bob
11 years ago

I agree with everyone, same pump and gauge for consistency. Over 100 psi I use the gauge on the shock pump. Under 100 I slightly over pump then use a 0~100 psi dial gauge with a bleeder valve to bleed it down to what I want. Same with tires, I took a dial gauge and cut the end off the hose and installed a presta fitting to set my tire pressure. I record my settings and after riding I make notes so I can adjust if needed the next time.

I have purchased 3 digital gauges and was not happy with any of them. Having to reset to check after adding or removing air took too much time.

RUSTYDOGG
RUSTYDOGG
11 years ago

I must be a caveman, but I don’t really use the gauge much. I go by the amount of sag. The gauge gets you in the vicinity.

Roger
Roger
11 years ago

I’m really glad so see such innovation in the cycling community. I need to get one of these because I always believed I would be an awesome mountain biker if I could get 94.3 psi in my front shock. Now I can!

JAVI
JAVI
11 years ago

What is the fox item number of this pump?

Smith McKenna
Smith McKenna
11 years ago

Fox is becoming the Apple of the biking scene. I won’t be buying anything else from them. They are getting ridiculous.

Graeme
Graeme
10 years ago

I bought 2 of these pumps, they work great BUT, after 6 months the battery is dying.
GUESS WHAT YOU CANT REPLACE THE BATTERY, YOU HAVE TO BUY ANOTHER NEW PUMP AT $70. I JUST CALLED FOX AND THAT IS WHAT THEY TOLD ME.

DO NOT BUT THESE, WHOEVER THOUGHT THE BATTERY WILL NEVER GO DEAD IS A …… AND THEY DIDNT TELL YOU ONCE ITS DEAD BUY A NEW PUMP AT $70 A POP.

DONT WASTE YOUR MONEY

JasApple
JasApple
9 years ago

UPDATE! I Second that @Graeme. DO NOT BUY THIS PUMP! THE BATTERY CAN NOT BE REPLACED!!!!!! HOW RIDICULOUS IS THAT!!! MINE DIED AFTER 4 MONTHS!! 70$ to use a shock maybe 25 times. HORRIBLE PRODUCT ONLY BECAUSE YOU CAN NOT REPLACE THE BATTERY!!! I REPEAT>> YOU CAN NOT REPLACE THE BATTERY!!! DO NOT BUY!!

Keith
Keith
8 years ago

I third this. Mine went bad after 4 months and only a few uses. it won’t hold a stead readying. I thought I was paying extra for a product that would last from a brand I trust, next time I’ll read these reviews in advance. Fox should be ashamed to provide and not support such a junky product. When I called them they said the pump was made by someone else with their logo, so return to place you bought it. that is unlikely possible. Fox, I’ve bought a lot of your stuff over the years, but you’ve just lost a chunk of business. When I think of buying something else…like a Fox vest, boots, helmet, I will think to buy something else.

Steve
8 years ago

Same here dead battery! 1 year. Sucks

Blair
Blair
7 years ago

Use some “Kiwi ingenuity” guys, carefully force it open & replace the battery inside, good to go again!

Zokinjo
Zokinjo
7 months ago
Reply to  Blair

I just carefully opened the housing and simply exchange the battery-CR2032. It works again…

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.