Home > Feature Stories

FSA BB30 vs BB386EVO – A Visual Comparison & Weights

Comparison of Pressfit BB30 and BB386EVO cranksets and bottom brackets weights and technical details
10 Comments
Support us! Bikerumor may earn a small commission from affiliate links in this article. Learn More

Comparison of Pressfit BB30 and BB386EVO cranksets and bottom brackets weights and technical details

When the BB386EVO standard was introduced with the BH Ultralight, we could almost hear the collective sigh around another standard. But on paper, it offers a lot of flexibility in its implementation and does allow frame manufacturers some impressive additional real estate at the bottom bracket shell.

While building up our Project MonsterCross bike, we started talking to FSA in more depth about the standard and how it can be used on non-386EVO frames. And, for that matter, why you’d even want to use it on a non-386EVO frame…

 

Comparison of Pressfit BB30 and BB386EVO cranksets and bottom brackets

Shown here are two FSA SL-K Light compact 110 BCD cranksets with 175mm arms. The one with black rings and silver spindle is a BB30 crankset (with 36/46 cyclocross rings). The other is BB386EVO with 34/50 compact rings. FSA gave the EVO spindle a gold hue simply for visual differentiation, making it quick and easy to identify which is which.

Comparison of Pressfit BB30 and BB386EVO cranksets and bottom brackets

Comparison of Pressfit BB30 and BB386EVO cranksets and bottom brackets

BB30 and Pressfit BB30 are based on a 68mm wide bottom bracket shell. BB386EVO has an 18.5mm longer spindle designed around an 86.5mm wide BB shell. The full spindle length obviously includes the space for the non-drive crank arm to mount and a wave spring that maintains proper bearing load.

Comparison of Pressfit BB30 and BB386EVO cranksets and bottom brackets

Because the EVO BB shell is wider, the arms must have less curvature. From FSA:

“Q-Factor is 146mm on both, the same as our BB30 and MegaExo cranks. In order to maintain that Q-Factor, we use slightly less arm curvature than a BB30 crank, but were still able to keep more than our MegaExo cranks. Ankle clearance can be a concern for some riders with excessive foot angle on the down stroke, but the curvature of the 386 EVO arms is at least as good, or better than industry standards.”

Comparison of Pressfit BB30 and BB386EVO cranksets and bottom brackets

Comparison of Pressfit BB30 and BB386EVO cranksets and bottom brackets

From the side, the cranks have a different profile. The EVO cranks (top) are a little more shapely with a bit of a bulge on the trailing edge at the pedal hole. FSA’s Matt VanEnkevort says it’s really just cosmetic, but gives it a “faster, more aggro look.”

Comparison of Pressfit BB30 and BB386EVO cranksets and bottom brackets

So it looks good, but is that all? Nope. The EVO crankarms are lighter and stiffer:

“There’s less material because it doesn’t have as much curvature, and a straighter arm is going to be stiffer,” VanEnkevort said. “It’s possible, and we haven’t tested this, but it’s possible that an EVO crankset might even be slightly stiffer (than the BB30 setup) in a BB30 frame.”

Comparison of Pressfit BB30 and BB386EVO cranksets and bottom brackets

Even with the larger overall set of rings and longer spindle, the EVO driveside parts are only 16g heavier. Take the 10g savings from the non-drive arm and we’re betting you’d come out just a bit lighter with the same chainring combo on each.

Comparison of Pressfit BB30 and BB386EVO cranksets and bottom brackets

Just for fun, there’s a 4g difference between standard (left) and ceramic bearing PFBB30 bottom brackets.

IMPLEMENTATION:

Question is, if you have a BB30 or PFBB30 frame, is there any reason to consider the wider BB386EVO cranks? Probably not, but:

“If you have a BB30 frame, the best solution is a straight up BB30 crankset,” says VanEnkevort. “The EVO advantage really comes when you have a frame with the wider, stiffer bottom bracket or for someone who’s either transferring it between EVO and BB30 frames or planning on upgrading their frame in the future.”

Currently, BH, Wilier and Litespeed offer BB386EVO frames.

FSA MW258 BB30 to BB386EVO bottom bracket adapters

If you do decide to run an EVO crankset on a BB30/PFBB30 frame, FSA offers simple spacers to fill the gap between the bottom bracket bearings and the crankarms.

For the Pressfit bottom brackets, the ones shown above are the same for either standard PFBB30 frames or EVO frames. The gray plastic shell between bearing cups slides open enough to accommodate the wider EVO frames, too.

GOING OFF BRAND:

The flip side is fitting a BB386EVO frames with other cranksets. While FSA was one of the original partners in developing the BB386EVO standard, they’re working on adapters for SRAM’s tapered GXP spindles and, eventually, Campagnolo’s UltraTorque cranksets, too. VanEnkevort says the Campy adapters require a bit more engineering to properly incorporate the retention rings necessary thanks to their split spindle design.

FSA PFBB30 to MegaExo and Shimano bottom bracket adapters

Shimano has had PFBB86 cranks for a while, but they use their standard 24mm diameter spindles. All that’s needed to run those cranks on an EVO frame is a reducer between the 30mm ID of the bearings and the 24mm OD of the spindle. FSA’s adapters (above) reduce BB30 down to 24mm ID for use with their MegaExo cranksets. Despite minute (we’re talking two spots right of the decimal) differences in actual spindle diameters between their MegaExo and Shimano cranks, FSA says these will work. We’ll test this in the near future. (FSA’s MegaExo is their outboard bearing setup)

And as a final word about the “new standard”, if you really think about it, BB386EVO is simply taking Shimano’s and Campy’s existing press fit 86mm standard and giving it the popular 30mm diameter spindle. Not exactly groundbreaking when you think of it that way, just sort of a natural evolution.

 

Subscribe
Notify of
guest

This site uses Akismet to reduce spam. Learn how your comment data is processed.

10 Comments
Oldest
Newest Most Voted
Inline Feedbacks
View all comments
Jzilla
Jzilla
12 years ago

Yeah FSA..

Perhaps the most condescending customer service in the industry. Some of their stuff is top shelf but when you have an issue they act like it is always YOUR fault.

I pretty much bet other shop guys have had the same experience.

Jzilla the clueless Burper
Jzilla the clueless Burper
6 years ago
Reply to  Jzilla

Burp……”

mb5150
mb5150
5 years ago
Reply to  Jzilla

oh yeah. I had the exact same experience. FSA is by far the worst customer service I have ever experience with anything to do with bikes. I had a crankset pedal insert come loose and contacted them regarding a replacement and they deemed the cranks “old and needing to be retired” after a 3 year lifespan

Gino
Gino
12 years ago

Can’t we all just get along!….
I do think BB30 is missing something.
I don’t like the use of wavey washers for end play adjustment…… and don’t even get me started on Campy…
but, I guess if manufacturers can produce a consistant BB shell size out of factories that shouldn’t be a problem…. but, then a lot of them are in carbon fiber now which I imagine is a little more difficult to get them all the same size,
each system has limitations, I guess….

Apollo
Apollo
12 years ago

Very straightforward explanation of the difference between the 2 standards. Very well done and useful. Thank you Tyler and Bike Rumor!

asmallsol
asmallsol
12 years ago

Jzilla, I totally agree with you. The bolt that held everything together on my SLK light crank which came on my CAAD 10 kept coming loose. FSA would blame cannondale and me. Too bad all three of the guys on my team who bought one had the exact same problem. It would loosen up in less than 100 miles, so on a 130 mile road race, I had a horrible squeak ever pedal stroke.

thebikegnome
thebikegnome
12 years ago

My Fuji comes with a Rotor 3d + f crankset with a pf86 bb. the bearings seem to be extra wide and less deep than typical. The crank has a 30mm spindle but the bb shell is standard pf 86. does 386 evo have a larger diameter bb OD ?

Jzilla
Jzilla
12 years ago

Thanx asmallsol

Jzilla
Jzilla
12 years ago

asmallsol – 12/25/11 – 8:59am
Jzilla, I totally agree with you. The bolt that held everything together on my SLK light crank which came on my CAAD 10 kept coming loose. FSA would blame cannondale and me. Too bad all three of the guys on my team who bought one had the exact same problem. It would loosen up in less than 100 miles, so on a 130 mile road race, I had a horrible squeak ever pedal stroke.

Peter
9 years ago

Hi, I was given a gossamer 386 crankset to be an upgrade on my fsa omega fitted to my standard non bb30 Boardman winter bike. I have the fsa spacers to fill the gaps between cups and cranks. Is that all I need?

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.