Home > Feature Stories

Fox Updates FIT, Pro Pedal, Gets Slicker and Adds Long Travel 29er, Ti-Crowned Forks

2012 fox 34 talas 29er suspension fork
16 Comments
Support us! Bikerumor may earn a small commission from affiliate links in this article. Learn More

2012 fox 34 talas 29er suspension fork

Fox Racing Shox has been one busy critter this winter…they’ve just introduced their new 34 series of long travel 29er forks, tweaked the tune on their FIT cartridges based on travel, improved internal and external seals, updated the Kashima coating and rolled it out across more forks and opened it up to OEM and figured out a way to make a stiff titanium crown/steerer tube.

UPDATED 4/19 – More info and a couple of tweaks to the original info notated throughout the post.

It’s a lot to cover, so dive on in after the break and see the future of Fox’s suspension technology…

2012-fox-34-talas-29er-suspension-fork

Given the growth of longer travel 29er bikes and the stunts riders are pulling on them, Fox saw fit to build a stronger fork. The new 34 class uses 34mm diameter stanchions and are built for longer travel 29ers, offering 140mm of travel. The lowers are beefier, too, evidenced by the massive arch shown above, developed to handle the stresses of the longer axle to crown distance on 140mm travel 29er forks.

There will be Float and TALAS (140 to 110) versions with Factory and Evolution options for OEM as of now, and Factory level for aftermarket. All of them will have tapered steerers and 15mm thru axles only. Available in July. They still have the 32-series for shorter travel XC bikes.

NEW FAMILY GROUPS

Mentioned above, you may wonder what Factory and Evolution are. For 2012 model year (and presumably beyond), Fox has grouped their forks into three categories:

  • FACTORY is best of the best and has all of their latest technology
  • PERFORMANCE is high end with FIT cartridges on most forks
  • EVOLUTION is the entry level with mostly open bath internals on forks

KASHIMA COATING

Introduced last year as an aftermarket option only, for 2012, Kashima coating is open to OEM also. If the plethora of bikes at other booths is any indication, you’ll be seeing it on pretty much every high-end mountain bike by mid-summer. It will be on all Factory level products.

Why the change? Kashima products are coated in Japan then built in Watsonville, CA, so there were logistics and shipping issues that they wanted to figure out before rolling it out across their entire product range. Fox has the exclusive on it, too, in case you missed that in the original news we posted. A new Kashima coat for 2012 models is a little darker and ever so slightly more slippery, which is really more of a cosmetic thing, and they get Kashima branding on the stanchion. Fox has heard from their athletes that the coating makes the sliders less susceptible to scratching, too.

2012 fox float rp23 and dhx shocks get the kashima coating

As previously leaked, their shocks have Kashima on the canister and Air Sleeve, too. In order to coat the piece, the entire piece has to be done, so the inside of the air canister is coated, too, meaning the main air seal slides on a smoother surface inside the shock.

Coilover shocks get a Kashima option on the shaft, too. Unrelated but interesting, the DHX RC4 has a boost valve adjustment called bottom out control that controls the ramp up in the last third of travel. The blue knob cranks down to adjust the volume of the boost valve chamber. Just FYI.

PRO PEDAL GETS ADAPTIVE LOGIC

2012 fox rp23 gets adaptive logic pro pedal upgrade

At the Factory level, the RP23 gets the new Adaptive Logic Pro Pedal, which flip-flops the way the switch works, sort of. On regular Pro Pedal, flicking the switch toward the air valve turns it on, with platform damping level determined by the number selected.

2012 fox adaptive logic pro pedal switch

First, notice that it’s no longer 1-2-3. It’s now 0-1-2. With Adaptive Logic Pro Pedal, you have the Pro Pedal platform damping available in both positions. Flick the switch toward the air valve and it’s automatically sets to a factory preset firmest level of damping. It’s still not a lockout, but it’s firmer than the current 3 setting. Flick it away from the air valve and you can adjust the low speed compression (ie. platform). At 0, it’s what they call a “free bleed” with no low speed compression, so it’s fully open. Settings 1 and 2 have increasing levels of platform (low speed compression) damping and give the shock a progressively firmer feel. In practice this lets you set the level of platform damping in the open position to suit the type of course you’re riding. Then, when the going gets fast or you hit a big climb, simply flick it closed (toward the air valve) and it automatically goes to the most efficient platform for hard pedaling…something racers should appreciate.

Additionally, on the Float RP23, they have a new High Definition Rebound that effectively doubles the number of detents on the knob to give a finer adjustment between fastest and slowest. Overall range of rebound damping hasn’t changed, just the number of clicks. Will be on Factory and Performance Float shocks.

WHAT THOSE TUNE NUMBERS MEAN ON THE SHOCKS

This isn’t new, but we thought you might want to know what those factory-set tune numbers mean that are printed on the shocks. Usually, they’re determined by working with the frame manufacturers to get the right shock based on leverage ratios and suspension designs. Here’s what they do:

  • Boost Valve tune = A position sensitive damping change based on the PSI in the Nitrogen chamber. A higher number means firmer valving earlier in the the compression stroke, which means more damping without changing the spring rate. For more on what Boost Valve actually is, check out this post.
  • Velocity Tune = Compression damping via valving, which overlaps a bit with the boost tune and is affected by ProPedal settings.
  • Rebound Tune = Rebound damping by shims and an orifice controlled by the rebound knob.

They also have different air sleeve and canister sizes that can adjust the air volume.

NEW FIT CARTRIDGES AND SEALS – THINGS GET SLIPPERY-ER

fox puts new FIT cartridges tuned for travel and with reduced friction seals in their 2012 forks
The 2010/2011 FIT cartridge seal on the left, 2012 on the right.

A new FIT seal head reduces friction, especially at the beginning of the movement. 2012 FIT Damper gets new internals, too. Last year they had just one tune for all forks. This year, they have an XC tune for 120mm of travel and less, and a Trail tune on anything 140mm and over. The XC tune has a firmer compression tune and the Trail tune has a bit softer low speed initial compression to make it more plush over rough terrain…but some of these changes for for RL and Remote models only, see update below:

UPDATE: This just in to clarify, directly from the FIT designer Sante Pelot:

“The trail tuned 130mm+ travel dampers are for FIT RL and FIT Remote only (because the user cannot adjust their low-speed compression setting as it is set at the factory). The trail tune is still firmer in low-speed compression than last year’s FIT RL or FIT Remote so that it is less wallowy/brake-divey than previous model years. For all FIT RLC, RL and Remotes we reduced the high-speed compression damping from last year so that the fork is less harsh on square-edge hits and drops to flat. But RLC’s are the same exact tune whether it is 80mm or 160mm of travel (because the user can adjust their low-speed compression setting to wherever they want it).”

2012 fox forks get new SKF seals that drastically reduce friction

On the outside, Fox has an exclusive partnership with SKF for seals on the outside of the fork that also noticeably reduce friction. Versus last year’s seals, the new SKF ones (on the right, marked by four dots around the outside) have a different compound, lip seal angle and shallower depth. They’ll ship on Factory level forks first then be a running change incorporated into the Performance and Evolution lines eventually. Only on forks for now, not shocks.

Just by a Fox fork and totally bummed to be reading this? Worry not: All retrofittable to forks from quite a ways back (at least 2006, but probably older than that) by sending your fork in for an upgrade. It’ll be about $320 with labor to replace the FIT cartridge and seals on a Float 32 RLC. That’s about $260 in parts, and the labor includes a general overhaul of your complete fork.

FORGET CARBON, FOX GOES WITH TITANIUM

2012 fox float ti fork with titanium crown and steerer tube

First shown at Interbike as a prototype, the 2012 Fox Float Ti comes in as low as 2.91lbs for the 80/100 FIT RLC w/ 9mm QR and goes up to 3.46lbs for the 120 FIT Terralogic w/ 15mm Thru Axle.

The Float Ti forks will only come with a tapered crown. Fox uses an investment cast 6/4 titanium crown/steerer that’s made in Oregon.

Why Ti versus carbon? Fox’s marketing manager Jim Noonan admits that carbon is a bit stiffer, but says the Ti can be lighter and offers a more resilient, supple ride with better high frequency vibration damping, and it’s exactly the same stiffness as their regular alloy 32-series crowns. Comes with a slim Kashima-coated alloy cap (below) with Ti bolt and expansion plug (no star nuts allowed). Available around August.

The Fox Float Ti gets alloy top caps with kashima coat and chiseled shaping to reduce weight

NEW REMOTES ON SOME MODELS

UPDATE: Just added this section 4/19.

  • The Shimano remote will be used on the FACTORY level. (45.81 grams, no cable) – Shimano unit has been in use by FOX already since MY2010.
  • The new FOX remote will be used on the Evolution level. (31.65 grams, no cable) – FOX unit is completely new for 2012

Of course, this begs the question of why the lighter one isn’t on the Factory models…

2012 MODEL YEAR PRICING & AVAILABILITY

UPDATE: Added this 4/19. Yeah, um, this is entirely too much to type, so you can download the pricing sheet as a PDF by clicking here. Availability is pegged at mid- to late summer 2011 depending on model, but we say TONS of them on demo bikes around Sea Otter, so you may be able to get it when buying a complete bike before then.

Subscribe
Notify of
guest

This site uses Akismet to reduce spam. Learn how your comment data is processed.

16 Comments
Oldest
Newest Most Voted
Inline Feedbacks
View all comments
Varaxis
Varaxis
12 years ago

I see they addressed FIT Damper stiction at the beginning of a stroke. I thought it was the wiper seals or something that was making thud sounds after long rides on a moderately rough track.

New propedal makes more sense too.

Nice to see Kashima coat on more forks, that will be coming to OEM, but I think they went a bit overboard by coating parts that don’t need it.

Primoz
Primoz
12 years ago

Which parts don’t need it?

greg
greg
12 years ago

poop-brown is the new black!
i like it. especially the ti crown, hopefully that will be offered in their 29 eventually.
the only part i see kashima coated that doesnt need it is the top cap, but it looks blingy.

Epic29r
Epic29r
12 years ago

Yes please Mr.Fox…..make mines in 29_TiTerralog100_9qr for our eastcoast trails.
At least the color matchs the kmc_sl chain.

Kovas
Kovas
12 years ago

Agree with Varaxis 100%.

Nice to see that Kashima is coating the entire Fox line of shox… But to see it put on non-essential bits (like the above mentioned alloy cap) is a shameful waste of precious natural resources. Fox should green-up a bit…Kashima coating uses a rare-earth substance called molybdenum (sulfide). Extracting molybdenum often requires flat-topping mountains. In some instances it requires several tons of raw ore to extract just a few mere grams of molybdenum… Think gold mines, platinum, etc…

There’s one thing to use a resource for what it’s needed, there’s another one to abuse it.

Shame on you FOX.

Ian
Ian
12 years ago

Kovas,

I guess I have a bit of a problem with your statement, mainly regarding the fact that almost everything you said is wrong. Firstly, molybdenum is mined through panel caving, not by removing mountain tops. Secondly, molybdenum is very abundant and a it doesn’t take anywhere close to a ton of ore to produce a few grams. If it did, it would cost similar to what gold costs, except it actually costs 500 times less. Not to mention the process of coating a fork or shock with molybdenum disulfide uses such a small amount that you probably only need a gram of it to coat at least 10 or 20 forks. The added demand of coating a top cap probably amounted to mining at most 10 more pounds of ore. I guess I just have problem claiming to be green when in fact they know nothing about it. Please check your facts.

gillis
gillis
12 years ago

@Kovas,

There is no way in hell that any Fox product is “green”, or going to be anytime, ever. If you really want to be green…go buy a rigid fork. Then go ride to the trailhead, then ride home (because the trails themselves really aren’t natural either). I could go on but no one should kid themselves into thinking mtb’ing is somehow an environmentally superior sport. That it doesn’t guzzle gas directly is its only saving grace. Even then, most drive to ride.

rant over

Robert
Robert
12 years ago

Perhaps Gillis would prefer everyone take up golf and knock some trees down for a fairway.

Anyway, I am glad I’ve waited a series of Fox products before updating. This stuff should work great and last. I can’t begin to think how they’ll up the ante unless it is weight or price reductions.

Kovas
Kovas
12 years ago

Ian – I’d say, take a tour of a Molybdenum mine and you’ll see exactly what I mean. Thanks for the correction about flat-topping vs. panel caving. … Then again, when whole mountains disappear from mining, does it really matter how they got that way?

Darin
Darin
12 years ago

So mining issues aside (really guys?!?) is there any hint as to when this stuff will be available? It says 2012, but that really doesn’t mean much these days regarding the release of components, bikes, cars, etc.

ShopMechanic
ShopMechanic
12 years ago

Why don’t they put those graphics from the TI fork on all of their forks? Simple is better guys!

Jeremiah Johnston
Jeremiah Johnston
12 years ago

Droooool… The graphics on the Ti fork are pretty sexy, agreed. I’m a little bummed I just went to 2011 Fox stuff across my whole line of bikes, but I’m sure I’ll survive the season til the new toys are available anyways. And I agree with Darin and Gillis both. We surely don’t ride lifts and drive an hour to the trails to save the planet; and the mining issue could be argued til doomsday without anyone’s opinions changing. Let’s keep oogling the new toys, and argue mining over beers at the trailhead while watching the sun set.

binny bin
binny bin
12 years ago

any word on a 140 or 150mm Ti version coming out in the future? thanks!

Stu
Stu
12 years ago

Ok, crack a beer. The Climax mine outside of Leadville, Colorado is a moly mine and I assure you that there is no “panel caving” going on there…there is a whole mountain missing. If that isnt flat topping Im not sure what is. (drink) You can mine for anything in many different ways ie. open pit, panel, flat top, placer, but in the end there are always environmental issues usually centered around water contamination via heavy metals. Unless you are a Quaker you are part of the problem. If you ride a bike for anything other than transportation you are part of the problem. (glug, glug) It’s a bummer but let’s, as mountain bikers not confuse ourselves as environmentalists. Oh ya, and molybdenum is not a rare earth metal but mining for it can sure wreck a back country experience. Nice forks, I hope to get one. (crush can and recycle)

BCManUCD
BCManUCD
12 years ago

How much molybdenum does kashima coating use vs. a steel frame (AKA Chrome-MOLY)?

KehBrodes
KehBrodes
12 years ago

Just got my Kashima coated rp23 on my new ibis frame. Cant wait to try it out! Goddamn snow and rain!!!!!!

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.

Subscribe Now

Sign up to receive BikeRumor content direct to your inbox.